Fore Innovations Camaro L1 Fuel System (dual pump)

Camaro L1 Fuel System (dual pump)

  • 800+ rwhp capacity, return fuel system
  • Uses OEM fuel rails

 

Clear
SKU: N/A Category:

Description

Fore Innovations Level 1 Dual Pump Fuel System for 2010-2015 5th Gen Camaro

Boost Referenced Return System for 800+ rwhp. Use with OEM fuel rails.

Kit Includes
• Camaro Fuel Pump Module – Dual Pump
• F1i Fuel Pressure Regulator
• 88mm Inline Fuel Filter
• FCV Checkvalve
• All fittings, hose, and hardware to complete typical fuel line plumbing.

Electrical Upgrade
None: base module configuration, 6″ [150mm] of pump power wire protrude from top of hermetic seal

FC2 Controller with 6 gauge wiring:
– Operates both pumps simultaneously, using factory control
– Best for controlling two small fuel pumps for street duty, or two large fuel pumps for track use only (due to fuel heat)
– May be used for control of secondary pumps with triple module IF [a small] primary pump can be run by OEM harness
– Includes 14′ [4.2m] of 6 AWG power wire and 100 amp fuse
– Includes 3′ [.9m] of 6 AWG ground wire with ring terminal
– Includes 7′ [2.1m] 12 AWG pump leads and sealed Delphi connector at pump module

FC3 Staged Controller with 4 gauge wiring:
– Operates secondary pump(s) independently from primary pump using factory control in conjunction with a secondary trigger source.
– Best for controlling two or three large fuel pumps for street duty and minimizing heat
– Includes 14′ [4.2m] of 4 AWG power wire and 100 amp fuse
– Includes 3′ [.9m] of 4 AWG ground wire with ring terminal
– Includes 7′ [2.1m] 12 AWG pump leads and sealed Delphi connector at pump module

Sealed Delphi Connector and 7′ 12 AWG pigtail only
– Includes 7′ [2.1m] 12 AWG pump leads and sealed Delphi connector at pump module
– Installer is responsible for properly implementing fuses and relays

Filtration Media
CELLULOSE FILTER ELEMENT
– cellulose element, bonded aluminum endcaps, Viton o-ring
– provides 10 micron nominal, 14 micron absolute filtration
– use with gasoline and race gas
– disposable
– recommended filtration for use with Injector Dynamics fuel injectors

MICROGLASS SSD (ANTI-STATIC) FILTER ELEMENT
– microglass element, static dissipating, bonded aluminum endcaps, Viton o-ring
– provides 12 micron absolute filtration
– use with all fuel types and blends (i.e. gasoline, race gas, E85, E100, M5, diesel)
– disposable
– recommended filtration for use with Injector Dynamics fuel injectors

STAINLESS FILTER ELEMENT
– stainless element, stainless endcaps, Viton o-ring
– provides 10 micron nominal, 26 micron absolute filtration
– use with all fuel types and blends (i.e. gasoline, race gas, E85, E100, M5, diesel)
-re-usable

Fuel Filter Upgrades
Upgrade to 128mm Filter
– Upgrade from standard 88mm filter to 128mm filter length for more filtration capacity and more time between service intervals.

Billet Mounting Bracket
– Use it to mount filter under car body, show quality installation to secure mounting of filter assembly for ease of maintenance

Filter Monitoring Gauge and Fitting
– Use to monitor fuel pressure before filter to inspect filter health. A higher pressure before filter indicates loss across the filter. If ignored, substantial filter obstruction will lead to reduced pump performance, shortened pump life, and higher fuel heat. Fitting is includes to allow precise orientation of pressure gauge.

System Options
Honeywell Pressure Switch for FC3
– 1/8 NPT Male threads, installs in intake manifold, must see boost and vacuum

Boost Vacuum Manifold Kit
– Our Boost / Vacuum manifold kit includes the following: Fore Innovations Boost / Vacuum Manifold (3 x 1/4″ barb fittings, 4 x plugs)

Additional information

Weight 15 lbs
Dimensions 24 × 12 × 12 in
Primary Fuel Pump

TI Auto F90000262 [ +$115.00 ], TI Auto F90000267 [ +$120.00 ], TI Auto F90000274 [ +$125.00 ], TI Auto F90000285 [ + $170.00 ], Walbro GSS342 [ +$90.00 ]

Secondary Fuel Pump(s)

TI Auto F90000262 [ +$115.00 ], TI Auto F90000267 [ +$120.00 ], TI Auto F90000274 [ +$125.00 ], TI Auto F90000285 [ +$170.00 ], Walbro GSS342 [ +$90.00 ]

Electrical Upgrade

FC2 Controller with 6 gauge wiring [ +$209.00 ], FC3 Staged Controller with 4 gauge wiring [ +$249.00 ], None (I have my own fuses, wiring, relays, etc), Sealed Delphi Connector and 7' 12 AWG pigtail only [ +$25.00 ]

Fuel Lines

FlexLP -8 Feed / Return, PTFE -8 Feed / Return, Startlite -8 Feed / Return

Filtration Media

Cellulose, Microglass SSD [ +$19.00 ], Stainless Steel [ +$32.00 ]

Reviews

There are no reviews yet.

Be the first to review “Fore Innovations Camaro L1 Fuel System (dual pump)”

Your email address will not be published. Required fields are marked *